Caterpillar 907 Wheel Loader Specs & Buying Research

At a glance

Key specifications

Operating Weight12,765 lb5,792 kgCaterpillar 907 — Weights. Published reference configuration; fitted options can vary.Manufacturer verified

Rated Net Power - ISO 924972.1 hp53.8 kWCaterpillar 907 — Engine. *Meets U.S. EPA Tier 4 Final and EU Stage V emission standards. Advertised power is tested per the specified standard in effect at the time of manufacture. Net power advertised is the power available at the flywheel. #Maximum gross and net torque measured at 1,600 rpm.Manufacturer verified

Height: Bucket Pin**10 ft 8 in3,251 mmISO 14397 · Caterpillar 907 — Dimensions - With HPL-V Coupler - Approximate#. *Vary with bucket **Vary with tire ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL),1.05 m3 (1.4 yd3) general purpose bucket. ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center). †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing. ††Full compliance to EN474-3 and SAE J1197. #HPL-A weight, tipping and rated loads are within 1% of the HPL-V. Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R18 tires and 1.05 m3 (1.4 yd3) general purpose bucket with bolt-on cutting edge or a class II fork carriage and tines, (tire supplier variability can impact dimensions by 2%). Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9.Manufacturer verified

Maximum Gross Power - SAE J199574.7 hp55.7 kWCaterpillar 907 — Engine. *Meets U.S. EPA Tier 4 Final and EU Stage V emission standards. Advertised power is tested per the specified standard in effect at the time of manufacture. Net power advertised is the power available at the flywheel. #Maximum gross and net torque measured at 1,600 rpm.Manufacturer verified

Overall dimensions

Length: Overall*17 ft 7.3 in5,366 mmManufacturer verified

Width: Over Tires6 ft 0.8 in1,848 mmManufacturer verified

Height: Ground to Cab**8 ft 6 in2,592 mmManufacturer verified

Measurement basis: Caterpillar 907 — Dimensions - With HPL-V Coupler - Approximate#. *Vary with bucket **Vary with tire ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL),1.05 m3 (1.4 yd3) general purpose bucket. ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center). †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing. ††Full compliance to EN474-3 and SAE J1197. #HPL-A weight, tipping and rated loads are within 1% of the HPL-V. Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R18 tires and 1.05 m3 (1.4 yd3) general purpose bucket with bolt-on cutting edge or a class II fork carriage and tines, (tire supplier variability can impact dimensions by 2%). Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9.

Precision visual reference

Dimensions and working range

Published measurements for the stated configuration. Illustration not to scale.

Reviewed visual

Caterpillar 907 Wheel Loader, illustrative side and front reference views; not a scale drawing. — Machine reference views

Overall Size

ALength: Overall*17 ft 7.3 in5,366 mmManufacturer verified

BWidth: Over Tires6 ft 0.8 in1,848 mmManufacturer verified

CHeight: Ground to Cab**8 ft 6 in2,592 mmManufacturer verified

Working Range

Height: Bucket Pin**10 ft 8 in3,251 mmManufacturer verified

Clearance: Bucket at 45° *8 ft 2.6 in2,505 mmManufacturer verified

Reach: Bucket at 45° *2 ft 4.1 in714 mmManufacturer verified

Length: Wheel Base7 ft 1.4 in2,170 mmManufacturer verified

Reference details

Overall measurement views reviewed 2026-09-06. Illustrative artwork, not a scale drawing.

Documented model generation; confirm serial/PIN and installed configuration · United States / North American reference

Canonical reference: heavyeq.ca/specs/wheel-loaders/caterpillar/907/ · Printed from HeavyEQ.ca. Confirm the actual machine and current manufacturer documentation before transport or operation.

Year, generation & configuration

Model generation and configuration

Generation / series: Current 907 manufacturer record
Applicable region: United States / North American reference
Year handling: Confirm the serial/PIN and production year when matching an individual machine to this reference.

Model identity

Model family, generation & status

Model family: Caterpillar 907
Generation / record: Current 907 manufacturer record
Product status: Current manufacturer model — status checked September 2026
Regional scope: United States / North American reference

No verified lineage relationship published. HeavyEQ reviewed first-party sources and did not force a predecessor or successor from model numbering.

United States / North American reference

Verified specifications

Values retain their cited source, verification status and original publication basis. Imperial is presented first while manufacturer-published dual units and configuration context remain attached to every value.

Qualified specifications with value-level verification status
Specification	Imperial	Metric	Standard / configuration	Source
Rated Net Power - ISO 9249	72.1 hp	53.8 kW	Caterpillar 907 — Engine. *Meets U.S. EPA Tier 4 Final and EU Stage V emission standards. Advertised power is tested per the specified standard in effect at the time of manufacture. Net power advertised is the power available at the flywheel. #Maximum gross and net torque measured at 1,600 rpm.Manufacturer verified	Caterpillar
Maximum Gross Power - SAE J1995	74.7 hp	55.7 kW	Caterpillar 907 — Engine. *Meets U.S. EPA Tier 4 Final and EU Stage V emission standards. Advertised power is tested per the specified standard in effect at the time of manufacture. Net power advertised is the power available at the flywheel. #Maximum gross and net torque measured at 1,600 rpm.Manufacturer verified	Caterpillar
Operating Weight	12,765 lb	5,792 kg	Caterpillar 907 — Weights. Published reference configuration; fitted options can vary.Manufacturer verifiedSafety-sensitive value — verify the exact machine.	Caterpillar
Length: Overall*	17 ft 7.3 in	5,366 mm	ISO 14397 · Caterpillar 907 — Dimensions - With HPL-V Coupler - Approximate#. Vary with bucket *Vary with tire ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL),1.05 m3 (1.4 yd3) general purpose bucket. ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center). †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing. ††Full compliance to EN474-3 and SAE J1197. #HPL-A weight, tipping and rated loads are within 1% of the HPL-V. Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R18 tires and 1.05 m3 (1.4 yd3) general purpose bucket with bolt-on cutting edge or a class II fork carriage and tines, (tire supplier variability can impact dimensions by 2%). Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9.Manufacturer verifiedSafety-sensitive value — verify the exact machine.	Caterpillar
Width: Over Tires	6 ft 0.8 in	1,848 mm	ISO 14397 · Caterpillar 907 — Dimensions - With HPL-V Coupler - Approximate#. Vary with bucket *Vary with tire ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL),1.05 m3 (1.4 yd3) general purpose bucket. ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center). †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing. ††Full compliance to EN474-3 and SAE J1197. #HPL-A weight, tipping and rated loads are within 1% of the HPL-V. Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R18 tires and 1.05 m3 (1.4 yd3) general purpose bucket with bolt-on cutting edge or a class II fork carriage and tines, (tire supplier variability can impact dimensions by 2%). Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9.Manufacturer verifiedSafety-sensitive value — verify the exact machine.	Caterpillar
Height: Ground to Cab**	8 ft 6 in	2,592 mm	ISO 14397 · Caterpillar 907 — Dimensions - With HPL-V Coupler - Approximate#. Vary with bucket *Vary with tire ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL),1.05 m3 (1.4 yd3) general purpose bucket. ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center). †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing. ††Full compliance to EN474-3 and SAE J1197. #HPL-A weight, tipping and rated loads are within 1% of the HPL-V. Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R18 tires and 1.05 m3 (1.4 yd3) general purpose bucket with bolt-on cutting edge or a class II fork carriage and tines, (tire supplier variability can impact dimensions by 2%). Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9.Manufacturer verifiedSafety-sensitive value — verify the exact machine.	Caterpillar
Height: Ground Clearance**	11.8 in	300 mm	ISO 14397 · Caterpillar 907 — Dimensions - With HPL-V Coupler - Approximate#. Vary with bucket *Vary with tire ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL),1.05 m3 (1.4 yd3) general purpose bucket. ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center). †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing. ††Full compliance to EN474-3 and SAE J1197. #HPL-A weight, tipping and rated loads are within 1% of the HPL-V. Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R18 tires and 1.05 m3 (1.4 yd3) general purpose bucket with bolt-on cutting edge or a class II fork carriage and tines, (tire supplier variability can impact dimensions by 2%). Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9.Manufacturer verifiedSafety-sensitive value — verify the exact machine.	Caterpillar
Height: Bucket Pin**	10 ft 8 in	3,251 mm	ISO 14397 · Caterpillar 907 — Dimensions - With HPL-V Coupler - Approximate#. Vary with bucket *Vary with tire ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL),1.05 m3 (1.4 yd3) general purpose bucket. ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center). †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing. ††Full compliance to EN474-3 and SAE J1197. #HPL-A weight, tipping and rated loads are within 1% of the HPL-V. Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R18 tires and 1.05 m3 (1.4 yd3) general purpose bucket with bolt-on cutting edge or a class II fork carriage and tines, (tire supplier variability can impact dimensions by 2%). Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9.Manufacturer verified	Caterpillar
Clearance: Bucket at 45° *	8 ft 2.6 in	2,505 mm	ISO 14397 · Caterpillar 907 — Dimensions - With HPL-V Coupler - Approximate#. Vary with bucket *Vary with tire ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL),1.05 m3 (1.4 yd3) general purpose bucket. ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center). †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing. ††Full compliance to EN474-3 and SAE J1197. #HPL-A weight, tipping and rated loads are within 1% of the HPL-V. Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R18 tires and 1.05 m3 (1.4 yd3) general purpose bucket with bolt-on cutting edge or a class II fork carriage and tines, (tire supplier variability can impact dimensions by 2%). Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9.Manufacturer verifiedSafety-sensitive value — verify the exact machine.	Caterpillar
Reach: Bucket at 45° *	2 ft 4.1 in	714 mm	ISO 14397 · Caterpillar 907 — Dimensions - With HPL-V Coupler - Approximate#. Vary with bucket *Vary with tire ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL),1.05 m3 (1.4 yd3) general purpose bucket. ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center). †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing. ††Full compliance to EN474-3 and SAE J1197. #HPL-A weight, tipping and rated loads are within 1% of the HPL-V. Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R18 tires and 1.05 m3 (1.4 yd3) general purpose bucket with bolt-on cutting edge or a class II fork carriage and tines, (tire supplier variability can impact dimensions by 2%). Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9.Manufacturer verifiedSafety-sensitive value — verify the exact machine.	Caterpillar
Length: Wheel Base	7 ft 1.4 in	2,170 mm	ISO 14397 · Caterpillar 907 — Dimensions - With HPL-V Coupler - Approximate#. Vary with bucket *Vary with tire ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL),1.05 m3 (1.4 yd3) general purpose bucket. ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center). †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing. ††Full compliance to EN474-3 and SAE J1197. #HPL-A weight, tipping and rated loads are within 1% of the HPL-V. Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R18 tires and 1.05 m3 (1.4 yd3) general purpose bucket with bolt-on cutting edge or a class II fork carriage and tines, (tire supplier variability can impact dimensions by 2%). Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9.Manufacturer verified	Caterpillar

What the specifications mean

The published 907 values remain attached to their stated configuration and rating basis.

Caterpillar 907 — Dimensions - With HPL-V Coupler - Approximate#. *Vary with bucket **Vary with tire ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL),1.05 m3 (1.4 yd3) general purpose bucket. ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center). †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing. ††Full compliance to EN474-3 and SAE J1197. #HPL-A weight, tipping and rated loads are within 1% of the HPL-V. Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R18 tires and 1.05 m3 (1.4 yd3) general purpose bucket with bolt-on cutting edge or a class II fork carriage and tines, (tire supplier variability can impact dimensions by 2%). Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9.

An individual machine must be verified by serial/PIN, installed equipment and actual measurements.

Configuration intelligence

Configurations & specification differences

These observations are scoped to the cited generation and region. They are not a list of valid option combinations.

Material configurations in this research record
Record	Verified observation	Scope
Lift configuration	Caterpillar 907 — Dimensions - With HPL-V Coupler - Approximate#. Vary with bucket *Vary with tire ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL),1.05 m3 (1.4 yd3) general purpose bucket. ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center). †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing. ††Full compliance to EN474-3 and SAE J1197. #HPL-A weight, tipping and rated loads are within 1% of the HPL-V. Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R18 tires and 1.05 m3 (1.4 yd3) general purpose bucket with bolt-on cutting edge or a class II fork carriage and tines, (tire supplier variability can impact dimensions by 2%). Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9.	Current 907 manufacturer recordUnited States / North American reference

A brochure configuration is not an individual marketplace machine. Serial/PIN and build information are required for exact verification.

Used 907 inspection priorities

Check centre articulation, steering cylinders, oscillation points and driveline play.
Inspect matched tires and load the lift, tilt and coupler hydraulics.
Verify payload, ride-control and technology systems only when installed.
Match the 907 model plate, fitted attachment and undercarriage to the cited reference configuration.

Configuration-aware inspection: these checks are triggered by machine category, installed configuration and technology package. Brochure-listed technology must be physically present, active, licensed and calibrated on the used machine.

Hours, condition and ownership cost

Hours are context, not a condition grade. Duty cycle, idle time, maintenance evidence, wear-system measurements, structural repairs and installed technology should be evaluated together.

Cost drivers to model

Tires, fuel, bucket wear and cycle duty dominate many loader cost profiles.
High-lift arms, couplers and application packages change repair exposure.
Payload planning must use material density and the fitted bucket.

Compatibility graph

Attachment considerations

Relationships below identify relevant classes only unless a stronger evidence state is shown. They never assert exact used-attachment fitment.

relevant attachment class

Loader buckets, forks and grapples

Verify coupler interface, attachment weight, load centre, hydraulics.

Open attachment research

Before confirming fitment

generation and machine configuration
mounting interface, coupler or pin geometry
hydraulic flow, pressure, return and case drain
attachment weight and machine capacity limits
electrical controls or required machine options

Model-reference transport profile

Transport reference

Reference measurements retain their configuration and verification status. Confirm the actual transport setup before booking.

Manufacturer verifiedOperating Weight12,765 lb5,792 kgCaterpillar 907 — Weights. Published reference configuration; fitted options can vary.

Manufacturer verifiedLength: Overall*17 ft 7.3 in5,366 mmCaterpillar 907 — Dimensions - With HPL-V Coupler - Approximate#. *Vary with bucket **Vary with tire ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL),1.05 m3 (1.4 yd3) general purpose bucket. ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center). †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing. ††Full compliance to EN474-3 and SAE J1197. #HPL-A weight, tipping and rated loads are within 1% of the HPL-V. Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R18 tires and 1.05 m3 (1.4 yd3) general purpose bucket with bolt-on cutting edge or a class II fork carriage and tines, (tire supplier variability can impact dimensions by 2%). Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9.

Manufacturer verifiedWidth: Over Tires6 ft 0.8 in1,848 mmCaterpillar 907 — Dimensions - With HPL-V Coupler - Approximate#. *Vary with bucket **Vary with tire ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL),1.05 m3 (1.4 yd3) general purpose bucket. ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center). †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing. ††Full compliance to EN474-3 and SAE J1197. #HPL-A weight, tipping and rated loads are within 1% of the HPL-V. Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R18 tires and 1.05 m3 (1.4 yd3) general purpose bucket with bolt-on cutting edge or a class II fork carriage and tines, (tire supplier variability can impact dimensions by 2%). Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9.

Manufacturer verifiedHeight: Ground to Cab**8 ft 6 in2,592 mmCaterpillar 907 — Dimensions - With HPL-V Coupler - Approximate#. *Vary with bucket **Vary with tire ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL),1.05 m3 (1.4 yd3) general purpose bucket. ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center). †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing. ††Full compliance to EN474-3 and SAE J1197. #HPL-A weight, tipping and rated loads are within 1% of the HPL-V. Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R18 tires and 1.05 m3 (1.4 yd3) general purpose bucket with bolt-on cutting edge or a class II fork carriage and tines, (tire supplier variability can impact dimensions by 2%). Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9.

Reference specifications can differ from the actual configured machine. Confirm dimensions and weight before booking transportation.

Confirm or replace before a transport request

actual weight
actual travel length, width and height
attachments and removable work tools
bucket, blade, carriage or boom position
loading condition

Source provenance

First-party sources and verification notes

Only manufacturer-authored records are linked publicly. Provisional measurements remain marked until a matching first-party record is confirmed.

Caterpillar

907 Compact Wheel Loader | Cat | Caterpillar

United States / North American reference · exact model technical page · accessed September 6, 2026 · status: Manufacturer verified

Open source